Binding Carpet Remnant Ends

Binding the remnant ends of the carpet rug on the floor of your house is a nice idea to keep the house neat. First of all you have to do is cut the loose threads of the carpet remnant with scissors. Use glue to bind the ends of the carpet remnant that are cut properly. You would do well to allow the glue to sufficiently dry.

The method suggested above would suit the carpets that are used in areas where upon you don’t find lot of people walking. The method suggested above would safeguard an inexpensive and an affordable carpet. This is so because as the time goes on a few more threads in the carpet may get loosened. The process has to be repeated in case you find some more threads of the carpet get loosened. Hot glue can be used in the process. Every time you have to allow the glue to dry properly.

Ideas for Washing High Windows Having Ledges

It is always true that you would find it difficult to clean high windows having ledges in your home. It can of course be done when certain tips are followed. You would do well to buy some effective window washing tools, such as a squeegee, a window bucket, soap and microfiber cloths. It is true that ledge comes in the way of cleaning.

It is interesting to note that you can make use of the ledge to your advantage while cleaning the high window. Remember that you have to clean the ledge in a nice way in order to make your high window look neat and great. If the ledge is unclean the process of cleaning the high window would go in vain. Clean the inside of the window well. An extension pole and the squeegee should be used to nicety to clean the inside of the high window of your house.

Making Your Carpet Beater

If you have household rugs and carpets then you would certainly need a carpet beater to clean them. It is easy to make one. Make use of an old garden hose by cutting from it a 3-foot long section. The hose has to be cut into vertical strips along the marks you create. Leave the hose uncut at about 4 inches of length at the end.

You may purchase a dowel that fits nicely into the modified hose section. The dowel has to be nicely trimmed by using a saw. The dowel should be 2 feet long. Take the help of the workmen from the hardware store in case you do not possess a saw to trim the dowel. The inside part of the portion of the hose kept uncut has to be smeared with a glue. The uncut part of the hose has to be knit into the dowel. Allow the glue to dry.

Covering your Windows for winters

Instructions

Use layered curtains to hang over your window for winters. These curtains are thick so they can effectively block light and noise. Install bubble wrap for your windows. Bubble wrap can be easily installed and will help in preventing cold air from outside coming in through the panes. The window should be moistened using water. Keep the wrap, against the window with bubble side down. The excess wrap should be removed.

Installation of cellular shades on your windows is also helpful. Cellular shades are useful in insulating your windows, still allowing light to be filtered in. Insulation film can be placed over your window. Insulation kits can be purchased at many hardware stores which contain insulation film along with double-sided tape. The film should be placed over the window attaching the film using the tape. Heat should be applied to shrink the film as well as to remove any wrinkles.

Plumbing the Bathroom Drains

Instructions

Using a funnel-cup Plunger

Buy a funnel-cup plunger for removing the clog in the toilet drain. These plungers form a solid seal to surround the opening of the toilet bowl, which helps to increase its suction power.

The rubber present on the plunger should be softened by running it over hot water to form a better seal. The plunger should be positioned directly over the clogged drain. Push the plunger down and then pull it back up, repeating this up-and-down movement many times. The clog gets removed allowing water to flow down your bathroom drain.

For unclogging a shower drain using a plunger you should smear a thin film of petroleum jelly around the edges of the cup. This forms a strong seal between the plunger and the drain. Hold the plunger on the shower drain to perform the up-and-down motion. Repeat this movement many times to release the debris.